Description
The AG Associates Heatpulse8108 rapid thermal anneal system contains a subsystem for each of the following: • Electronics (including a dedicated microprocessor) • Mass-flow-controlled gas handling • Cooling • ULPA filtration • Mechanical assemblies Software programs, called recipes, specify the details for each process. The AG Associates Heatpulse 8108 system includes a 3-1/2-inch floppy disk drive for process recipe storage. A three-axis industrial robot automates processing by transporting wafers into and out of the process chamber. It uses closed-loop feedback for precise motion control and accurate positioning. To provide cold-wall processing, water is circulated through the process-chamber walls. The quartz isolation tube is cooled with nitrogen or compressed air. AG Associates Heatpulse 8108 Rapid Thermal Anneal equipment APPLICATIONS: The Heatpulse 8108 system is a versatile tool which can be useful for many applications, such as (but not limited to): • Silicon dielectric growth • Implant annealing • Glass re-flow • Silicide formation and annealing • Nitridation of metals • Contact alloying • Oxygen donor annihilation AG Associates Heatpulse 8108 Physical Dimensions Width Monitor-Fab-Wall configurations: 40 in. (102 cm) Monitor-Side-Panel configurations: 60 in. (152 cm) Depth 42 in. (107 cm) Height 82 in. (208 cm) Weight Monitor-Fab-Wall configurations: 1800 lbs (816 kg); Monitor-Side-Panel configurations: 1840 lbs (835 kg) Shipping weight Monitor-Fab-Wall configurations: 2000 lbs (907 kg); Monitor-Side-Panel configurations: 2040 lbs (925 kg)Configuration
The following are the operating specifications for the Heatpulse® 8108 system. Wafer handling: automatic serial processing, using standard cassettes. Throughput: Process dependent, approximately 80 wafers per hour (in a null cycle) without flat-finder. Wafer sizes: 5 inches, 6 inches, and 8 inches (standard). Ramp-up rate: Programmable, 1 – 180°C per second. Steady-state duration: 1 – 600 seconds per step. Ramp-down rate: Programmable, 1 – 180°C per second. Ramp-down rate is temperature and radiation dependent, maximum 150°C per second. Recommended steady-state temperature range: 400 – 1200°C. ERP temperature accuracy: +3°C to -7°C, when calibrated against an instrumented thermocouple wafer (ITC). Temperature repeatability: + 3°C or better at 1150°C wafer to wafer. (Repetition specifications are based on a 100-wafer set.) Temperature uniformity: + 5°C across an 8-inch wafer at 1150°C. (This is a 1-sigma deviation from 100-angstrom oxide uniformity.) For a titanium silicidation process, no more than 1.5 percent increase to uniformity during the first anneal at 650 – 700°C.OEM Model Description
Rapid Thermal Processor The AG Associates Heatpulse 8108 system is a single-wafer, cassette-to-cassette rapid thermal processor, capable of processing in inert or corrosive ambients. The system is built for the production environment.Documents
No documents
CATEGORY
RTP/RTA
Last Verified: 10 days ago
Key Item Details
Condition:
Refurbished
Operational Status:
Unknown
Product ID:
138382
Wafer Sizes:
8"/200mm
Vintage:
Unknown
Logistics Support
Available
Transaction Insured by Moov
Available
Refurbishment Services
Available
Similar Listings
View All
METRON / AG ASSOCIATES
HEATPULSE 8108
RTP/RTAVintage: 1995Condition: Used
Last VerifiedOver 60 days ago
METRON / AG ASSOCIATES
HEATPULSE 8108
RTP/RTAVintage: 2003Condition: Used
Last VerifiedOver 60 days ago
METRON / AG ASSOCIATES
HEATPULSE 8108
RTP/RTAVintage: 1996Condition: Used
Last VerifiedOver 60 days ago
METRON / AG ASSOCIATES
HEATPULSE 8108
CATEGORY
RTP/RTA
Last Verified: 10 days ago
Key Item Details
Condition:
Refurbished
Operational Status:
Unknown
Product ID:
138382
Wafer Sizes:
8"/200mm
Vintage:
Unknown
Logistics Support
Available
Transaction Insured by Moov
Available
Refurbishment Services
Available
Description
The AG Associates Heatpulse8108 rapid thermal anneal system contains a subsystem for each of the following: • Electronics (including a dedicated microprocessor) • Mass-flow-controlled gas handling • Cooling • ULPA filtration • Mechanical assemblies Software programs, called recipes, specify the details for each process. The AG Associates Heatpulse 8108 system includes a 3-1/2-inch floppy disk drive for process recipe storage. A three-axis industrial robot automates processing by transporting wafers into and out of the process chamber. It uses closed-loop feedback for precise motion control and accurate positioning. To provide cold-wall processing, water is circulated through the process-chamber walls. The quartz isolation tube is cooled with nitrogen or compressed air. AG Associates Heatpulse 8108 Rapid Thermal Anneal equipment APPLICATIONS: The Heatpulse 8108 system is a versatile tool which can be useful for many applications, such as (but not limited to): • Silicon dielectric growth • Implant annealing • Glass re-flow • Silicide formation and annealing • Nitridation of metals • Contact alloying • Oxygen donor annihilation AG Associates Heatpulse 8108 Physical Dimensions Width Monitor-Fab-Wall configurations: 40 in. (102 cm) Monitor-Side-Panel configurations: 60 in. (152 cm) Depth 42 in. (107 cm) Height 82 in. (208 cm) Weight Monitor-Fab-Wall configurations: 1800 lbs (816 kg); Monitor-Side-Panel configurations: 1840 lbs (835 kg) Shipping weight Monitor-Fab-Wall configurations: 2000 lbs (907 kg); Monitor-Side-Panel configurations: 2040 lbs (925 kg)Configuration
The following are the operating specifications for the Heatpulse® 8108 system. Wafer handling: automatic serial processing, using standard cassettes. Throughput: Process dependent, approximately 80 wafers per hour (in a null cycle) without flat-finder. Wafer sizes: 5 inches, 6 inches, and 8 inches (standard). Ramp-up rate: Programmable, 1 – 180°C per second. Steady-state duration: 1 – 600 seconds per step. Ramp-down rate: Programmable, 1 – 180°C per second. Ramp-down rate is temperature and radiation dependent, maximum 150°C per second. Recommended steady-state temperature range: 400 – 1200°C. ERP temperature accuracy: +3°C to -7°C, when calibrated against an instrumented thermocouple wafer (ITC). Temperature repeatability: + 3°C or better at 1150°C wafer to wafer. (Repetition specifications are based on a 100-wafer set.) Temperature uniformity: + 5°C across an 8-inch wafer at 1150°C. (This is a 1-sigma deviation from 100-angstrom oxide uniformity.) For a titanium silicidation process, no more than 1.5 percent increase to uniformity during the first anneal at 650 – 700°C.OEM Model Description
Rapid Thermal Processor The AG Associates Heatpulse 8108 system is a single-wafer, cassette-to-cassette rapid thermal processor, capable of processing in inert or corrosive ambients. The system is built for the production environment.Documents
No documents